PIC32MX370F512H SPI2 NOT WORK (brigth)
Hi, I'm porting a correctly working project from PIC32MX340F512H (MPLAB IDE 8.92, XC32 compiler v1.22, ICD3) to PIC32MX370F512H ( MPLAB X IDE v3.20, XC32 compiler v 1.22, ICD3). The new PIC32MX370F512H...
View ArticleUSB drivers for cdc_com_port_single with custom board (sunugal)
Dear community, I am new to the USB protocol. I am working with a custom board that uses a PIC32MZ2048EFM144 to communicate through USB with a host PC. I am using MPLAB Harmony v2.02b and MPLAB X...
View ArticleCAN channel functions (FFB_Boy)
Hi,Actually I drive 8 CANOPEN slave with my PIC (PIC32MX795). I send packet slave by slave , So it take my 8 loops to update all my slave. On the documentation I see that the compiler 32 channels . Is...
View ArticlePIC32 with GSM module, sending email app (GerhardJL)
Hi All, I am not sure if this is in the correct forum channel - Please re-direct me to the correct forum channel for further posting. I would like to build an app to allow sending of emails,using a...
View ArticleGSM AT Command SIM800 (Sharvinda)
hII am not sure this IS the correct forum FOR GPS quiz. Please re-direct if wrong forum, my further posting. please help me to get SIM tool kit in SIM800, i tried to access " AT +STKMENU=? " and "...
View ArticlePIC32MM failed to program device after modifying PWRCON (jkano)
Hello, I'm experiencing some weird behaviour with new PIC32MM0064GPL020 device. We bought them because of the very low current on sleep mode with RAM retention and RTCC still working on this mode....
View ArticlePIC32MM - How to setup a PWM?? (thiagomg95)
Hi, I'm new with the PIC32 family and I'm using a PIC32MM0064GPL028. I'm trying to setup a standard PWM on pin RP19, with a 10 KHz frequency for a 90% Duty Cycle. I'm totally lost with the Datasheet,...
View ArticleLCD displays junk character if USB-MSD is enabled (newbee_pic32)
I am using pic32mx Microcontroller. My system clock and peripheral clock is 10MHz. I am using an LCD 16X2 display. With this setup everything is working fine i.e LCD display is proper. I have added USB...
View ArticlePIC32 UART Baud Rate Generator (MikeNES103)
Hi, After looking at the UART datasheet, I'm left a little bit puzzled about the Baud Rate Generator tables available at page 13 (DS61107G-page 21-13). At the moment, I use a PBC of 10 MHz. Why are...
View ArticleHow to use SPI channel in Logic analyzer simulator in MPLABXv3.51 (nome)
HI all, I have a PIC32MX230F064B. I have written a program to for SPI channel to interface with a sd card. I thought of first simulating it in MplabX simulator with logic analyzer and IO pins. This is...
View ArticleC32 for linux is required (AKSHAY D BHAVSAR)
I dont find C32 compiler for linux on microchip download archieves.Can anybody please provide me link to download same.?..
View ArticlePIC32MZ Ethernet (Nivin)
Hello,I'm new to PIC32MZ .I want to configure the TCP/IP,SMTP,IPv6 in this.I have DM320007-C development board.I couldn't find any application for the development board.I also started learning Harmony...
View ArticlePIC32 PWM and Idle (nsilvan)
Hi First some information:MCU: pic32mx250f128bMPLAB X: Version 3.51Compiler: xc32 LinuxRunning in Simulator. I'm trying to get a PWM signal while sending the CPU to Idle (since I don't use the CPU in...
View ArticlePIC32MZ2048EFH144 - CAN Module ISR is called twice for every message off the...
Hi All, I'm using Harmony v1.10 to configure the PIC32MZ2048EFH144 to use 2 CAN BUS ports running at 256 Kbps with 32 Tx buffers and 32 Rx buffers.I can receive and transmit messages without any...
View ArticleLive Update (jlehman)
I am trying to build a Harmony 1.08.01 live update application with XC32 1.42. When I build the live update example project the c init code is in the boot loader region and I cannot find any bank...
View Articlespi 2 clock TRIS configuration (swatvv)
hi, both spi 1 and spi 2 in slave mode.i using pic32mx120f064h and xc32 compiler and mplabx ide.i use both spi1 and spi2 . configuring spi 1, 35 th pin is SCK1 and PORF (RF6). There is no configuration...
View ArticleDid you ever used the BlueKitchen's BTStack libraries on PIC32? (thoraz)
Hi. I have a PAN1325B Bluetooth module with a CC256x TI's chipset inside. I want to use this module in my PIC32 project to create a simple SPP Server for a data stream. I noticed that this module needs...
View ArticlePIC32MZ Touchscreen (Kostakis)
Hello,I am using PIC32MZ2048EFH144 development board with MEB II. I just finished the prototyping and i am now going to start designing my own board. My problem is the Touchscreen and the touch...
View ArticleAfter writing Program Flash - I get data bus errors after a reboot. (danthony)
After writing Program Flash - I get data bus errors after a reboot. I am working with a modified version of the "web_server_nvm_mpfs" application. Using PIC32MZ2048EFG. I am erasing and write a page at...
View ArticleException when trying to read SPI from an interrupt routine (Vathek)
Hello,I have a custom board with an SPI ADC (AD7734) and a PIC32MX575F512L and I'm using Harmony 1.10 I managed to get SPI working and I can easily communicate with the ADC. Now I need to get ADC...
View Article
